DFRobot

This is a piezoresistive force sensor. The harder you press, the lower the sensor's resistance. Pressing lightly, the resistance changes from infinite to ~300k. The sensor itself is thin and...

This is a piezoresistive force sensor. The harder you press, the lower the sensor's resistance. Pressing lightly, the resistance changes from infinite to ~300k. The sensor itself is thin and flexible, but the resistance does not change while being flexed. Resistance changes only when pressure is applied to the round area at the end of the sensor. Used as a presence sensor (someone standing), weight sensor, pressure sensor (impact testing), etc. The overall length is about 8.5". Sensor comes...

This Gravity Analog 20A current sensor is based on the Hall current sensing principle. It can be used for AC or DC current measurement, has a wide voltage range, a small footprint, requires no...

This Gravity Analog 20A current sensor is based on the Hall current sensing principle. It can be used for AC or DC current measurement, has a wide voltage range, a small footprint, requires no soldering and has a high level of precision.We have added high-voltage isolation in the circuit design for safety reasons and a non-conductive acrylic plate has been attached to the bottom of the PCB to prevent accidents such as short circuits, electric shocks and any other potential danger.This...

This is a breakout board for the fully integrated Hall Effect based linear ACS758 current sensor. The sensor gives precise current measurement for both AC and DC signals.The thickness of the copper...

This is a breakout board for the fully integrated Hall Effect based linear ACS758 current sensor. The sensor gives precise current measurement for both AC and DC signals.The thickness of the copper conductor allows survival of the device at high overcurrent conditions. The ACS758 outputs an analog voltage output signal that varies linearly with sensed current. This current sensor enables you to monitor currents in your project every second for energy saving or circuit protecting purposes. This...

nt to measure AC current it is impractical and hazardous to cut in to your live wiring. The analog AC current sensor developed by DFRobot is a good solution to this problem. Using induction you can...

nt to measure AC current it is impractical and hazardous to cut in to your live wiring. The analog AC current sensor developed by DFRobot is a good solution to this problem. Using induction you can measure AC current without intrusive methods. Place your AC wire inside the unit, connect the unit to the sensor board using the 3.5mm jack connector and connect the sensor board to an analog input on your microcontroller. Use this sensor to measure AC motors, lighting equipment, air compressors or...

What sensor should you use when you need to measure temperature? Most people will think of a DS18B20 temperature sensor first, but this sensor is only capable of measuring temperatures up to 125C....

What sensor should you use when you need to measure temperature? Most people will think of a DS18B20 temperature sensor first, but this sensor is only capable of measuring temperatures up to 125C. In order to measure temperatures greater than 100C you will need something with a greater temperature range and resistance. This is the sensor you need! We have used a PT100 resistance type high temperature probe which is often used in industrial applications. Using this probe you can measure a...

This is an Arduino compatible piezo film vibration sensor. It is made up of flexible piezo film and converter board. The sensor is able to detect vibration, flexibility, impact and touch.The film is...

This is an Arduino compatible piezo film vibration sensor. It is made up of flexible piezo film and converter board. The sensor is able to detect vibration, flexibility, impact and touch.The film is a flexible component comprising a 28 µm thick piezoelectric PVDF polymer film with screen-printed Ag-ink electrodes, laminated to a 0.125 mm polyester substrate, and fitted with two crimped contacts. As the piezo film is displaced from the mechanical neutral axis and bending creates very high...

This is a BH1750 light intensity sensor breakout board with a 16 bit AD converter built-in which can directly output a digital signal, there is no need for complicated calculations. This is a more...

This is a BH1750 light intensity sensor breakout board with a 16 bit AD converter built-in which can directly output a digital signal, there is no need for complicated calculations. This is a more acurate and easier to use version of the simple foto resistor which only outputs a voltage that needs to be calculated in order to obtain meaningful data. With the BH1750 Light Sensor intensity can be directly measured by the luxmeter, without needing to make calculations. The data which is output by...

This is a three axis accelerometer for the LilyPad system. Based on the ADXL335 accelerometer from Analog Devices, the LilyPad Accelerometer can detect joint movement as well as inclination and...

This is a three axis accelerometer for the LilyPad system. Based on the ADXL335 accelerometer from Analog Devices, the LilyPad Accelerometer can detect joint movement as well as inclination and vibration.The ADXL335 outputs a 0V to 3V analog signal on each of the X, Y, and Z axis. You will need to convert this analog voltage to a gravity amount and use trigonometry to calculate a true 'angle'. If you are not looking for tilt, it is very easy to use this sensor for basic motion sensing.LilyPad...

Do you want to add a pair of eyes to your robot? This image sensor can do it.Pixy is a smart vision sensor you can quickly "teach" your robot to find objects. It saves your time by only outputting...

Do you want to add a pair of eyes to your robot? This image sensor can do it.Pixy is a smart vision sensor you can quickly "teach" your robot to find objects. It saves your time by only outputting the object data you're interested in. Pixy is flexible - use it with the microcontroller of your choice. It connects directly to Arduino with the included cable, and fully supports Raspberry Pi and BeagleBone Black with included software libraries. It comes with mounting hardware to attach to your...

This RS-485 Sensor Node module can be used in various applications such as intelligent agriculture, environment monitoring, home automation...etc. It is a Internet of things device. This RS-485...

This RS-485 Sensor Node module can be used in various applications such as intelligent agriculture, environment monitoring, home automation...etc. It is a Internet of things device. This RS-485 Sensor node provides 6 channel analog input and 1 SHT1x Humidity & Temperature digital input. The RS485 protocol supports up to 254 nodes at 1200m distance between each node. This allows a wide range cover for monitoring the environment. A screw free design allows easy connection of cables without...

This Sensor/Motor Drive Board (Cortex M3 CPU) is the integration of multiple communication interfaces that quickly build robotic systems. This board (Cortex M3 CPU) features the SPI Interface and...

This Sensor/Motor Drive Board (Cortex M3 CPU) is the integration of multiple communication interfaces that quickly build robotic systems. This board (Cortex M3 CPU) features the SPI Interface and works as a bridge between the whole system. There are many types of sensors on the board such as I2C bus communication protocol sensors, Ultrasonic sensors, SP03 TTS, CMP03 electronic compass, RS485-bus sensors, analog output sensors, infrared distance sensors, gyro sensors, acceleration sensors, and...

This SHARP infrared distance sensor takes a continuous distance reading and returns a corresponding analog voltage with a range of 20cm (8") to 150cm (60"). It can be usually applied as obstacle...

This SHARP infrared distance sensor takes a continuous distance reading and returns a corresponding analog voltage with a range of 20cm (8") to 150cm (60"). It can be usually applied as obstacle avoidance and path planning sensor.|Specification| Detection Range :20-150cm (7.9-59'') Voltage :4-5 .5 V Current :33-50 mA current consumption Output: analog output, the output voltage is proportional to detection range|Documents| Datasheet ...

This Infrared Proximity Sensor made by Sharp (model: GP2Y0A41SKOF) has an analog output which varies from 3.1V (4cm) to 0.3V (30cm) with a supply voltage between 4.5 and 5.5V DC. This sensor is...

This Infrared Proximity Sensor made by Sharp (model: GP2Y0A41SKOF) has an analog output which varies from 3.1V (4cm) to 0.3V (30cm) with a supply voltage between 4.5 and 5.5V DC. This sensor is great for sensing objects up to 30 cm away. It has a Japanese Solderless Terminal (JST) Connector which is compatible with our JST accessories. SHARP GP2Y0A41SKOF Infrared Distance Sensor Related Projects:Project 1: How To DIY a Robot with Function of Gap AvoidanceWhen the robot wanders around and...

The GP2Y0A710K infrared sensor is a new version of GP2Y0A700K which takes a continuous distance reading and reports the distance as an analog voltage with a distance range of 1m (39.3") to 5.5m...

The GP2Y0A710K infrared sensor is a new version of GP2Y0A700K which takes a continuous distance reading and reports the distance as an analog voltage with a distance range of 1m (39.3") to 5.5m (216.5").The interface is 5-wire JST connector (included with pins) with dual Vcc, dual Gnd, and a single output voltage. Power, ground and signal wiring is enough to read a continuous analog voltage representing distance. A software lookup table can be implemented to translate the voltages to...

Sharp optical dust sensor has an internal infrared diode and a phototransistor diagonally arranged. The diode projects light and the phototransistor detects the dark spots caused by the fine...

Sharp optical dust sensor has an internal infrared diode and a phototransistor diagonally arranged. The diode projects light and the phototransistor detects the dark spots caused by the fine particles passing through. In addition to this feature, depending on the pulse pattern outputted you can check whether or not is smoke or dust. This is the sensor you will need if you want to measure air particles, build an air purifier system, or detect certain particles. Includes a special cable to...

This SHT20 I2C temperature & humidity sensor is equipped with waterproof probe. It comes with the 4C CMOSens® SHT20 temperature & humidity sensor chip and the probe has gone through dual...

This SHT20 I2C temperature & humidity sensor is equipped with waterproof probe. It comes with the 4C CMOSens® SHT20 temperature & humidity sensor chip and the probe has gone through dual waterproof protection test.The SHT20 I2C temperature & humidity sensor adopt Sensirion techniques. Except the humidity sensor of capacitive type and the temperature sensor of band gap , SHT20 contains an amplifier, A/D converter, OTP memory and a digital processing unit. Compared with early SHT1x series...

This time we reinvented the line-tracking sensor. Beyond recognizing two specific colors or output through digital or analog only, the Smart Gray Sensor has integrated both digital and analog output...

This time we reinvented the line-tracking sensor. Beyond recognizing two specific colors or output through digital or analog only, the Smart Gray Sensor has integrated both digital and analog output features. In digital mode, user can have two color data recorded through simple button operation, to achieve two-color detections with high and low outputs, and requires no more configuration after being set. In analog mode, the output value reacts precisely to the color grayscale detected. Apart...

This low cost SFR02 ultrasonic ranger has both I2C and Serial interfaces. New AutoTune algorithms intelligently back the minimum range right up to the transducer ringdown for the very best...

This low cost SFR02 ultrasonic ranger has both I2C and Serial interfaces. New AutoTune algorithms intelligently back the minimum range right up to the transducer ringdown for the very best performance possible, automatically, in the background, and with no calibration cycles necessary. Additional new commands allow for separate burst and ranging control.The SRF02 arduino ultrasonic sensor features both I2C and a Serial interfaces. The serial interface is a standard TTL level UART format at...

Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to &;plusmn;16 g. Digital output data is...

Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to &;plusmn;16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface. The ADXL345 is well suited to measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high...

This Triple Axis Accelerometer with Bosch BMA220 is an ultra small triaxial, low-g acceleration sensor breakboard with SPI and I2C interface, aiming for low power consumer market applications. It...

This Triple Axis Accelerometer with Bosch BMA220 is an ultra small triaxial, low-g acceleration sensor breakboard with SPI and I2C interface, aiming for low power consumer market applications. It allows measurement of accelerations in 3 perpendicular axes and thus senses tilt, motion, shock and vibration in cell phones, handhelds, computer peripherals, man-machine interfaces, virtual reality features and game controllers. With a size of only 2 mm x 2 mm, the Bosch BMA220 represents a new...

3-Axis acceleration sensor is an electronic equipment which could measure the acceleration during the object motion. It could help you to analyse the target motion position or direction. The typical...

3-Axis acceleration sensor is an electronic equipment which could measure the acceleration during the object motion. It could help you to analyse the target motion position or direction. The typical interactive application could be the posture recognition and action recognition, such as WII game applications. These video game device are all using internal acceleration sensor, calculate the current motion direction by conversion algorithm. And most of the recent smart device are based the same...

The MMA7361 from Freescale is a very nice IMU sensor with easy analog interface. The MMA7361 Arduino is a 3.3V part and outputs an analog voltage for each of the three outputs. This voltage is in...

The MMA7361 from Freescale is a very nice IMU sensor with easy analog interface. The MMA7361 Arduino is a 3.3V part and outputs an analog voltage for each of the three outputs. This voltage is in ratio to the measured acceleration and to the supply voltage (ratiometric). It has selectable sensitivity by dip switch. You will need some extra hardware to convert this analog signal to a usable digital one. The Arduino is really good option for it. This break board is especially designed for...

This rubber ring is used to afix ultrasonic sensor. It fits URM37 V4.0 Ultrasonic Sensor For Arduino / Raspberry Pi and URM04 Ultrasonic Sensor (RS485). NOTE: Other ultrasonic sensor may fit, you...

This rubber ring is used to afix ultrasonic sensor. It fits URM37 V4.0 Ultrasonic Sensor For Arduino / Raspberry Pi and URM04 Ultrasonic Sensor (RS485). NOTE: Other ultrasonic sensor may fit, you have to check the dimensions.|Specification| Material: Rubber Inside diameter: 16mm Outside diameter: 26mm Thickness: 10mm|ShippingList| Rubber ring x1 ...

The URM04 Ultrasonic sensor is developed based upon our popular URM37 ultrasonic sensor, it is using RS485 interface which allows multiple sensors to be used simultaneously . The RS485 interface...

The URM04 Ultrasonic sensor is developed based upon our popular URM37 ultrasonic sensor, it is using RS485 interface which allows multiple sensors to be used simultaneously . The RS485 interface allows a number of sensors working together. Up to 32 URM04 may be connected together in a network. The ultrasonic sensor allows you to determine the exact distance of an obstacle in the sonar field of view. The cleverness of your robot will depend on a sensitive sensor similar to the one bats use to...

Ultrasonic sensors emit ultrasonic pulses, and by measuring the time of ultrasonic pulse reaches the object and back to the transducer, the distance of sensor from the target object is calculated....

Ultrasonic sensors emit ultrasonic pulses, and by measuring the time of ultrasonic pulse reaches the object and back to the transducer, the distance of sensor from the target object is calculated. They are widely used in detecting displacement, thickness, distance, water level, material level and transparent objects. The URM06 - Analog Ultrasonic sensor provides very short to long-range detection and ranging from 20cm ~ 10m, comes in a compact, robust PVC housing and matches 35mm electrical...

Ultrasonic sensors emit ultrasonic pulses, and by measuring the time of ultrasonic pulse reaches the object and back to the transducer, the distance of sensor from the target object is calculated....

Ultrasonic sensors emit ultrasonic pulses, and by measuring the time of ultrasonic pulse reaches the object and back to the transducer, the distance of sensor from the target object is calculated. They are widely used in detecting displacement, thickness, distance, water level, material level and transparent objects. The URM06 - PULSE Ultrasonic sensor provides very short to long-range detection and ranging from 20cm ~ 10m, comes in a compact, robust PVC housing and matches 35mm electrical...

An ultrasonic sensor measures distance by calculating the time difference between sending a signal and receiving an echo from an object. It uses echolocation to measure distances, just like a...

An ultrasonic sensor measures distance by calculating the time difference between sending a signal and receiving an echo from an object. It uses echolocation to measure distances, just like a bat.The URM07 is an ultra low-power sensor. The effect range is up to 7.5m, and it has a wide range power supply of 3.0 - 5.5V. It is directly compatible with 3.3V or 5V devices such as Arduino, Raspberry Pi. etc. The average operating current is only 5mA and standby current is only 14uA.According to the...

Most ultrasonic distance sensors aren't waterproof which can be a problem if you need your project to withstand the elements outdoors. No need to worry any more! We have developed waterproof...

Most ultrasonic distance sensors aren't waterproof which can be a problem if you need your project to withstand the elements outdoors. No need to worry any more! We have developed waterproof ultrasonic distance sensors with a waterproof sealed emitter. This sensor is suitable for outdoor applications such as car reversing sensors, security alarms, industrial inspection, etc. What will you make?Note: V2 has increased its resolution and accuracy.|Specification| Operating Voltage: 5V DC Static...

Most ultrasonic distance sensors aren't waterproof which can be a problem if you need your project to withstand the elements outdoors. No need to worry any more! We have developed waterproof...

Most ultrasonic distance sensors aren't waterproof which can be a problem if you need your project to withstand the elements outdoors. No need to worry any more! We have developed waterproof ultrasonic distance sensors with a waterproof sealed emitter. This sensor is suitable for outdoor applications such as car reversing sensors, security alarms, industrial inspection, etc. What will you make? |Specification| Operating voltage: DC5V Static current: 5mA Operating current: 30mA Operating range:...

The DFRobot heart rate sensor is a thumb-sized heart rate monitor designed for Arduino microcontrollers.This heart rate monitor sensor is a pulse sensor which is developed based on PPG techniques....

The DFRobot heart rate sensor is a thumb-sized heart rate monitor designed for Arduino microcontrollers.This heart rate monitor sensor is a pulse sensor which is developed based on PPG techniques. This is a simple and low-cost optical technique that can be used to detect blood volume changing in the microvascular bed of tissues. It is relatively easy to detect the pulsatile component of the cardiac cycle according to this theory. The sensor has two holes that you can use to attach to your...

This is a 8-pin female header which is used on Arduino board. |ShippingList| 8 Pin Header x10

This is a 8-pin female header which is used on Arduino board. |ShippingList| 8 Pin Header x10

These are a longer version of our standard break away headers. They are 10mm long which allows you use them socket to socket. The plastic separator can be slid up or down to accommodate your needs....

These are a longer version of our standard break away headers. They are 10mm long which allows you use them socket to socket. The plastic separator can be slid up or down to accommodate your needs. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. It is used on Arduino Ethernet Shield.|ShippingList| 40 Pin Header x10

This is a blue colored 40 Pin 2.54 mm?0.1"? single row pin header strip from DFRobot. These 0.1" header strips are commonly used as low-cost Arduino connectors. The standard spacing allows use with...

This is a blue colored 40 Pin 2.54 mm?0.1"? single row pin header strip from DFRobot. These 0.1" header strips are commonly used as low-cost Arduino connectors. The standard spacing allows use with solderless breadboards, perforated prototyping PCBs, female headers, and our premium and pre-crimped jumper wires. The single-row header strips can easily be snapped into smaller strips to fit your application. These colored pin headers will help you label pin rails depending on their function. We...

A row of right angle headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers.|ShippingList| 40 Pin Header x10 ...

A row of right angle headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers.|ShippingList| 40 Pin Header x10

These customized colored pin headers are extensively used in DFRobot's product range. For instance, we are the first who uses 3 colors to clearly indicate the roles that pin headers play: green -...

These customized colored pin headers are extensively used in DFRobot's product range. For instance, we are the first who uses 3 colors to clearly indicate the roles that pin headers play: green - digital; blue - analog; red - powerWe hope these tiny colorful pin headers help you in your own prototyping,PCB designing projects. Enjoy making! |Applications| Prototyping Arduino processor or shield female headers Custom pcb design|Specification| Pins are spaced by 0.1". Arduino processor R3 header...

Geared DC Motor and Housing Simple, cheap DC geared motor for those applications when steppers or servos are over kill or too costly. We love cheap DC motors and use them by the dozen so we thought...

Geared DC Motor and Housing Simple, cheap DC geared motor for those applications when steppers or servos are over kill or too costly. We love cheap DC motors and use them by the dozen so we thought it was about time we offered them to you. These are easy to run with an H-Bridge and integrate into your projects at a very cost effective price point. We hope you enjoy. Note: They come as a pair. 2x DC motors and 2x gearboxes. Suggested Voltage: 3V DC        ...

This is a 4.8-46V, 2A Dual Motor Controller which is the revised version of the DF-MDV1.0. Its performance has been improved greatly. It can bear larger current due to the increased heat-sink...

This is a 4.8-46V, 2A Dual Motor Controller which is the revised version of the DF-MDV1.0. Its performance has been improved greatly. It can bear larger current due to the increased heat-sink dissipation. It is easy to control, using LGS's outstanding high-power motor driver chip, the L298N. This chip allows for direct drive of two bi-directional DC motors, and incorporates high-speed short diodes for protection. Drive current up to 2A per motor output. The driver uses a broad-brush design to...

This is a TT Micro DC Geared Motor with Back Shaft working at 6V with 160rpm. The TT motor series the most popular DC motors for DIY enthusiasts. It is designed to easily incorporate the DFRobot...

This is a TT Micro DC Geared Motor with Back Shaft working at 6V with 160rpm. The TT motor series the most popular DC motors for DIY enthusiasts. It is designed to easily incorporate the DFRobot Encoder. These motors are inexpensive, small, easy to install, and ideally suited for use in a mobile robot. The DFRobot ROMEO microcontroller is able to complete the closed-loop PID making use of the Gravity:TT Motor Encoders Kit. We recommend this rubber wheel for this motor. |Specification|Electrical...

This ball caster used for MiniQ robot is a white ABS housing, a 3/8" diameter metal ball, two spacers (1/16" and 1/8" thick), and two #2 screw sets.The total height of this ball caster is 0.4" with...

This ball caster used for MiniQ robot is a white ABS housing, a 3/8" diameter metal ball, two spacers (1/16" and 1/8" thick), and two #2 screw sets.The total height of this ball caster is 0.4" with no spacers. You can also adjust the height by adding the spacers.The ball caster is used in our widely popular MiniQ sereis. |ShippingList| Ball caster x1 Screws x2

This box of grease is very small, light and easy to carry. It can be uesd in many places. It is suitable for the condition of light load or high speed plastic gear, plastic parts, nylon retainer...

This box of grease is very small, light and easy to carry. It can be uesd in many places. It is suitable for the condition of light load or high speed plastic gear, plastic parts, nylon retainer bearing lubrication, protection and noise reduction. You will need it for your robot and 3D Printer. |Specification| Net Weight : 5g|ShippingList| Grease(5g) x1

This is a gear motor with encoder. It is a motor with a 34:1 gearbox and an integrated quadrature encoder that provides a resolution of 11 pulse single per round giving a maximum output of 374...

This is a gear motor with encoder. It is a motor with a 34:1 gearbox and an integrated quadrature encoder that provides a resolution of 11 pulse single per round giving a maximum output of 374 within one round. With an Arduino controller and motor driver, applications for this include a closed-loop PID control or PWM motor speed control. This motor is an ideal option for mobile robot projects. The copper output shaft, embedded thread and reinforced connector greatly extends the motor's service...

Do you need a servo for a tiny little project? Or are you seeking for an affordable solution? This mini metal servo is quite impressive, it does quite the job for a large range of tasks. With metal...

Do you need a servo for a tiny little project? Or are you seeking for an affordable solution? This mini metal servo is quite impressive, it does quite the job for a large range of tasks. With metal gear, it could gives you a 1.8kg*cm torque. Pretty strong regarding its size. Suitable for Beam robots and other automation tasks. Keep in mind that if you need some heavy lifting you should be considering some of our other options. This servo is for you if you are planning on building smaller size...

This is a motor revolution: a new DC brushless motor with built-in motor driver. It can be conncected to Arduino directly without external motor driver. What's more, the motor comes with directional...

This is a motor revolution: a new DC brushless motor with built-in motor driver. It can be conncected to Arduino directly without external motor driver. What's more, the motor comes with directional control, PWM speed control and speed feedback output, which make this motor to be controlled easily. This product is convenient for mobile robotic platform since there is less drive pin and less MCU resource consumption.|Specification| Operating Voltage: 12V Stall current: 0.7A Motor rated speed:...

DSS-M15S is a heavy-duty metal gear standard servo with 270°wide angle, high torque power, improved stability and durability.Able to take in 6V and deliver a strong torque power of over 15Kg,...

DSS-M15S is a heavy-duty metal gear standard servo with 270°wide angle, high torque power, improved stability and durability.Able to take in 6V and deliver a strong torque power of over 15Kg, this tough 270°servo will never let you down when you need it. Tested with high load capacity for 12 hours long, this DSS-M15S servo demonstrates a maximum torque of 18Kg without much vibration or heat.In addition, we enclose carefully selected steering parts, including an aluminum alloy wheel and...

Herkulex DRS-0101 is state of the art modular smart servos incorporating motor, gear reducer, control circutry and communications capability in one single package, which can provide up to 12kg.cm at...

Herkulex DRS-0101 is state of the art modular smart servos incorporating motor, gear reducer, control circutry and communications capability in one single package, which can provide up to 12kg.cm at 7.4v. Equipped with a lot of adapting pieces including Horn, Horn Bolt(BHT 2.6X8), Wheel Horn Bushing, Wheel Horn Washer, Wheel Horn Bolt(PHM 3X8), Cable Guard, I-type Joint, L-type Joint, L-type Joint(Single Nut), Bracket Bolt(PHT 2X5), Joint Bolt(PHM 2X5), Wire Harness(200mm) and with it's...

Herkulex DRS-0201 is state of the art modular smart servos incorporating motor, gear reducer, control circutry and communications capability in one single package. Through metal brush coreless DC...

Herkulex DRS-0201 is state of the art modular smart servos incorporating motor, gear reducer, control circutry and communications capability in one single package. Through metal brush coreless DC motor, it can provide torque up to 24kg.cm at 7.4v. Equipped with a lot of adapting pieces including Horn, Horn Bolt(BHT 2.6X8), Wheel Horn Bushing, Wheel Horn Washer, Wheel Horn Bolt(PHM 3X8), Cable Guard, I-type Joint, L-type Joint, L-type Joint(Single Nut), Bracket Bolt(PHM 2X5), Joint Bolt(PHM...

Herkulex DRS-0401 is state of the art modular smart servos incorporating motor, gear reducer, control circutry and communications capability in one single package. Through Premium FAULHABER Coreless...

Herkulex DRS-0401 is state of the art modular smart servos incorporating motor, gear reducer, control circutry and communications capability in one single package. Through Premium FAULHABER Coreless DC Motor, this servo can provide the stall torque up to 5.1 N.m at 14.8V, which is really amazing. Equipped with serial adapting pieces including Horn, Horn Bolt(M 3*6), Bracket Assembly Bolt(M 2.6*4), Wire Harness(200mm,7.87") and with it's amazing structure, DRS-0401 is extremely easy to...

DSS-M15S servos have been well received by customers in these years. It has extremely wide angle range control, huge load capacity and excellent quality. This DSS-M15S with analog feedback has...

DSS-M15S servos have been well received by customers in these years. It has extremely wide angle range control, huge load capacity and excellent quality. This DSS-M15S with analog feedback has broken its internal potentiometer signal. This is an analog signal with 0~3.3V feedback. You can connect it to MCU to realize close-loop feedback control.DSS-M15S 270° Metal servo with feedback is compatible with Arduino Servo library. You can drive it with Arduino Board and read the angle value from...

This 130 DC motor has an integrated transistor built in to the board, eliminating the need for a motor driver. Use PWM to control it for all your DIY project needs. It uses the 3 pin "gravity"...

This 130 DC motor has an integrated transistor built in to the board, eliminating the need for a motor driver. Use PWM to control it for all your DIY project needs. It uses the 3 pin "gravity" interface saving lots of messy wiring.|Specification| Operating Voltage: 5v Interface type: Gravity 3-pin digital sensor interface Dimension: 2 * 1 in (52 * 27 mm) Weight: 40 g|Documents| Product Wiki More Documents |ShippingList| Gravity: 130 DC motor x1 Fan module x1 Gravity digital cable x1 ...

Gravity IO Expansion Shield with Motor Driver is a new product designed for Arduino Boards. It combines IO Expansion Shield and DC Motor Driver Shield, equipped with Gravity sensor interface and...

Gravity IO Expansion Shield with Motor Driver is a new product designed for Arduino Boards. It combines IO Expansion Shield and DC Motor Driver Shield, equipped with Gravity sensor interface and TB6612FNG dual motor driver. It also has XBee socket, I2C interface and UART port, makes the connections more convenient.With TB6612FNG dual channel motor driver IC, the shield can drive 2x1.2A DC motors at the same time. It supports PWM speed control, each channel can output 1.2A continuous current...

The HS-311 is the perfect servo for inexpensive applications. Do not let the price fool you though, this servo features many of the same aspects of more expensive servos. One peice circuit board and...

The HS-311 is the perfect servo for inexpensive applications. Do not let the price fool you though, this servo features many of the same aspects of more expensive servos. One peice circuit board and tight mesh gears ensures great durability. Comes with a number of various servo horns and arms with mounting hardware.This servo can operate 180° when given a pulse signal ranging from 600usec to 2400usec.|Specification| Speed: 0.19 sec/60° at 4.8V Speed: 0.15 sec/60° at 6.0V Torque:...

How can your robot rule the world with an iron fist but without any claw?This robot gripper is designed for all your gripping needs. It is made from injection molded industrial ABS and comes with 2...

How can your robot rule the world with an iron fist but without any claw?This robot gripper is designed for all your gripping needs. It is made from injection molded industrial ABS and comes with 2 Hitec's HS311 metal servos.Gripper opens to 1.3" and is able to rotate 180 degrees with the addition of a second servo at the rear.You can directly drive this gripper with our servo library on IO Expansion Shield V7. |Specification| Working Voltage:4.8-6V Clamp range:0-1.3" Marerial: ABS...

This is a metal DC geared motor, 100% pure copper coils, high-density molecular layer, 50:1 metal reducer, small size, large torque. The maximum torque could arrive 42 kg.cm, stable and durable!...

This is a metal DC geared motor, 100% pure copper coils, high-density molecular layer, 50:1 metal reducer, small size, large torque. The maximum torque could arrive 42 kg.cm, stable and durable! |Specification| Rated voltage: 12 VGear reduction ratio: 50:1D output shaft diameter: 6 mmNo-load speed: 100 RPM @ 12 vNo-load current: 0.17 ARated speed: 93 RPM @ 12 vCurrent rating: 0.68 ARated torque: 7 kg.cmStall torque: 42 kg.cmStall current: 2.19 APower: 5WWeight: 210 g|ShippingList| Metal DC...

This is a metal DC geared motor, 100% pure copper coils, high-density molecular layer, 100:1 metal reducer, small size, large torque. The maximum torque could arrive 50 kg.cm, stable and durable!...

This is a metal DC geared motor, 100% pure copper coils, high-density molecular layer, 100:1 metal reducer, small size, large torque. The maximum torque could arrive 50 kg.cm, stable and durable! |Specification| Rated voltage: 12 V Gear reduction ratio: 100:1 D output shaft diameter: 6 mm No-load speed: 50 RPM @ 12 v No-load current: 0.17 A Rated speed: 45 RPM @ 12 v Current rating: 0.68 A Rated torque: 9 kg.cm Locked-rotor torque: 50 kg.cm Locked-rotor current: 2.19 A Power: 5W Weight: 210...

This is a metal DC geared motor, 45:1 metal reducer. It has a small size and large torque. The maximum torque could arrive 4.5 kg.cm. It is stable and durable!|Specification| Rated Voltage: 6 V...

This is a metal DC geared motor, 45:1 metal reducer. It has a small size and large torque. The maximum torque could arrive 4.5 kg.cm. It is stable and durable!|Specification| Rated Voltage: 6 V Operating Voltage Range 2~7.5V Gear reduction ratio: 45:1 D output shaft diameter: 4 mm No-load speed: 133 RPM @ 6 v No-load current: 0.13 A Locked-rotor torque: 4.5 kg.cm Locked-rotor current: 2.3 A Operating Temperature: -20?60? Weight: 90 g|Documents| Dimension |ShippingList| Metal DC Geared Motor -...

This is a metal DC geared motor, 45:1 metal reducer. It has a small size and large torque. The maximum torque could arrive 1.2 kg.cm. It is stable and durable!|Specification|Rated Voltage: 6...

This is a metal DC geared motor, 45:1 metal reducer. It has a small size and large torque. The maximum torque could arrive 1.2 kg.cm. It is stable and durable!|Specification|Rated Voltage: 6 VOperating Voltage Range 2~7.5VGear reduction ratio: 45:1Gearbox length: 21 mm"D" shape shaft diameter: 4 mmNo-load speed: 15 RPM @ 6VNo-load current: 50 mA Locked-rotor torque: 1.2 Kg.cmLocked-rotor current: 0.6 AOperating Temperature: -20?60?Weight: 68 g|ShippingList|Metal DC Geared Motor - 6V 15RPM...

This is a metal DC geared motor, 34:1 metal reducer. It has a small size and large torque. The maximum torque could arrive 1 kg.cm. It is stable and durable!|Specification|Rated Voltage: 6...

This is a metal DC geared motor, 34:1 metal reducer. It has a small size and large torque. The maximum torque could arrive 1 kg.cm. It is stable and durable!|Specification|Rated Voltage: 6 VOperating Voltage Range 2~7.5VGear reduction ratio: 34:1Gearbox length: 21 mm"D" shape shaft diameter: 4 mmNo-load speed: 214 RPM @ 6VNo-load current: 50 mA Locked-rotor torque: 1 Kg.cmLocked-rotor current: 0.6 AOperating Temperature: -20?60?Weight: 68g|ShippingList|Metal DC Geared Motor - 6V 191RPM 1Kg.cm...

This is a metal DC geared motor, 362:1 metal reducer. It has a small size and large torque. The maximum torque could arrive 7.5 kg.cm. It is stable and durable!|Specification|Rated Voltage: 6...

This is a metal DC geared motor, 362:1 metal reducer. It has a small size and large torque. The maximum torque could arrive 7.5 kg.cm. It is stable and durable!|Specification|Rated Voltage: 6 VOperating Voltage Range 2~7.5VGear reduction ratio: 362:1Gearbox length: 27 mm"D" shape shaft diameter: 4 mmNo-load speed: 20 RPM @ 6VNo-load current: 50 mA Locked-rotor torque: 7.5 Kg.cmLocked-rotor current: 0.6 AOperating Temperature: -20?60?Weight: 74 g|ShippingList|Metal DC Geared Motor - 6V 20RPM...

This is a metal DC geared motor, 99:1 metal reducer. It has a small size and large torque. The maximum torque could arrive 2.5 kg.cm. It is stable and durable!|Specification|Rated Voltage: 6...

This is a metal DC geared motor, 99:1 metal reducer. It has a small size and large torque. The maximum torque could arrive 2.5 kg.cm. It is stable and durable!|Specification|Rated Voltage: 6 VOperating Voltage Range 2~7.5VGear reduction ratio: 99:1Gearbox length: 23 mm"D" shape shaft diameter: 4 mmNo-load speed: 15 RPM @ 6VNo-load current: 50 mA Locked-rotor torque: 2.5 Kg.cmLocked-rotor current: 0.6 AOperating Temperature: -20?60?Weight: 72 g|ShippingList|Metal DC Geared Motor - 6V 15RPM...

This is a metal DC geared motor, 75:1 metal reducer. It has a small size and large torque. The maximum torque could arrive 1.9 kg.cm. It is stable and durable!|Specification|Rated Voltage: 6...

This is a metal DC geared motor, 75:1 metal reducer. It has a small size and large torque. The maximum torque could arrive 1.9 kg.cm. It is stable and durable!|Specification|Rated Voltage: 6 VOperating Voltage Range 2~7.5VGear reduction ratio: 75:1Gearbox length: 23 mm"D" shape shaft diameter: 4 mmNo-load speed: 97 RPM @ 6VNo-load current: 50 mA Locked-rotor torque: 1.9 Kg.cmLocked-rotor current: 0.6 AOperating Temperature: -20?60?Weight: 74 g|ShippingList|Metal DC Geared Motor - 6V 15RPM...

This is a Gear Motor w/Encoder, model No. GB37Y3530-12V-90EN. It is a powerful 12V motor with a 90:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 16 counts per...

This is a Gear Motor w/Encoder, model No. GB37Y3530-12V-90EN. It is a powerful 12V motor with a 90:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 16 counts per revolution of the motor shaft, which corresponds to 1440 counts per revolution of the gearbox’s output shaft. These units have a 0.61" long, 6 mm-diameter D- shaped output shaft. This motor is intended for use at 12V, though the motor can begin rotating at voltages as low as 1V.The face plate...

This is a Gear Motor w/Encoder, model No.GB37Y3530-12V-251R. It is a powerful 12V motor with a 43.8:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 16 counts per...

This is a Gear Motor w/Encoder, model No.GB37Y3530-12V-251R. It is a powerful 12V motor with a 43.8:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 16 counts per revolution of the motor shaft, which corresponds to 700 counts per revolution of the gearbox’s output shaft. These units have a 0.61" long, 6 mm(0.24")-diameter D- shaped output shaft. This motor is intended for use at 12V, though the motor can begin rotating at voltages as low as 1V. The face...

This is a Gear Motor w/Encoder, model No. GB37Y3530-12V-83R. It is a powerful 12V motor with a 131:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 16 counts per...

This is a Gear Motor w/Encoder, model No. GB37Y3530-12V-83R. It is a powerful 12V motor with a 131:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 16 counts per revolution of the motor shaft, which corresponds to 2096 counts per revolution of the gearbox&;rsquo;s output shaft. These units have a 0.61" long, 6 mm(0.24")-diameter D- shaped output shaft. This motor is intended for use at 12V, though the motor can begin rotating at voltages as low as 1V. The face...

This is a metal geared DC motor w/Encoder. It is a 6V motor with a 75:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 11 counts per revolution of the motor shaft,...

This is a metal geared DC motor w/Encoder. It is a 6V motor with a 75:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 11 counts per revolution of the motor shaft, which corresponds to 823.1 counts per revolution of the gearbox’s output shaft.PinmapThese units have an 10 mm length, 4 mm-diameter D-shaped output shaft. This motor is intended for use at 6V, though the motor can begin rotating at voltages as low as 1V. This motor is an ideal option for your...