Sensors

"The Weather Shield is an easy to use Arduino shield that grants you access to barometric pressure, relative humidity, luminosity and temperature. There are also connections on this shield to...

"The Weather Shield is an easy to use Arduino shield that grants you access to barometric pressure, relative humidity, luminosity and temperature. There are also connections on this shield to optional sensors such as wind speed, direction, rain gauge and GPS for location and super accurate timing. These Weather Shields utilize the HTU21D humidity, MPL3115A2 barometric pressure, and ALS-PT19 light sensors and relies on the HTU21D and MPL3115A2 Arduino libraries. Each shield comes with two...

This is the same temperature sensor that is included in our SparkFun Inventor's Kit. The TMP36 is a low voltage, precision centigrade temperature sensor. It provides a voltage output that is...

This is the same temperature sensor that is included in our SparkFun Inventor's Kit. The TMP36 is a low voltage, precision centigrade temperature sensor. It provides a voltage output that is linearly proportional to the Celsius temperature. It also doesn't require any external calibration to provide typical accuracies of ±1°C at +25°C and ±2°C over the −40°C to +125°C temperature range. We like it because it's so easy to use: Just give the device a ground and 2.7 to 5.5 VDC and read the...

36" high temperature Type-K Thermocouple with glass braid insulation. Features: Type-K Thermocouple (Ni-Cr) 30 gauge stripped and prepped wires Thermocouple range : -270 to +1372C (-454 to...

36" high temperature Type-K Thermocouple with glass braid insulation. Features: Type-K Thermocouple (Ni-Cr) 30 gauge stripped and prepped wires Thermocouple range : -270 to +1372C (-454 to +2501F) Glass braid insulation range : -73 to +482C(-100 to +900F) Yellow + / Red - Works great with our Thermocouple Amplifier AD595 IC!

    The fiber optic Temperature Probe TP-01 is a high precision temperature probe for use in a wide temperature range. It is for the temprature measuring of air/solid, but not...

    The fiber optic Temperature Probe TP-01 is a high precision temperature probe for use in a wide temperature range. It is for the temprature measuring of air/solid, but not for liquid. It is a point-like probe housed in a stainless steel tube and with a connector at one end. you can also find the Thermocouple_K_Female Connetor to integrate this sensor to your PCBA Features Length:100cm Measuring Range:-50 - +400 response time: 5s ...

Tilt-a-Whirl Breakout - RPI-1031 Description: The RPI-1031 tilt sensor is capable of sensing a change in orientation in four different directions: forward, back, left or right. This breakout...

Tilt-a-Whirl Breakout - RPI-1031 Description: The RPI-1031 tilt sensor is capable of sensing a change in orientation in four different directions: forward, back, left or right. This breakout board makes it easier to incorporate the RPI-1031 in your next project by breaking the necessary pins out to standard 0.1" spaced headers. This board will work at either 3.3 or 5V. Documents: Schematic Eagle Files Datasheet (RPI-1031) Product Page(RPI-1031) Hookup Guide bildr Tutorial Product...

    This is a new version of infrared distance switch. It has small size and higher ranging, it is able to detect ranging from 3cm to 100cm. It is tiny, easy to use/assemble, and...

    This is a new version of infrared distance switch. It has small size and higher ranging, it is able to detect ranging from 3cm to 100cm. It is tiny, easy to use/assemble, and inexpensive. Useful for robotics, interactive media, industrial assembly line, etc. Specification Power supply: 3.8v-5.5v Current(5v): 6mA Range: 3-100cm adjustable Wiki & External links Wiki link ...

    This is a breakout board for Freescale's MMA7361L three-axis analog accelerometer. The sensor requires a very low amount of power and has a g-select input which switches the...

    This is a breakout board for Freescale's MMA7361L three-axis analog accelerometer. The sensor requires a very low amount of power and has a g-select input which switches the accelerometer between ?1.5g and ?6g measurement ranges. Other features include a sleep mode, signal conditioning, a 1-pole low pass filter, temperature compensation, self test, and 0g-detect which detects linear freefall. Zero-g offset and sensitivity are factory set and require no external devices....

These easy-to-use ultrasonic rangefinders from Maxbotix work the same way as the EZ line that you know and love, but this new high-resolution series features 1 millimeter resolution! As with the...

These easy-to-use ultrasonic rangefinders from Maxbotix work the same way as the EZ line that you know and love, but this new high-resolution series features 1 millimeter resolution! As with the rest of the Maxbotix range finders, these sensors feature Analog Voltage, RS232 Serial, and Pulse Width outputs making them easy to interface with any microcontroller. These sensors have a maximum range of 5000 mm (195 inches) with virtually no dead zone (although objects closer than 30 cm will...

This is the fantastically easy to use sensor from Maxbotix. We are extremely pleased with the size, quality, and ease of use of this little range finder. The serial interface is a bit odd (it's...

This is the fantastically easy to use sensor from Maxbotix. We are extremely pleased with the size, quality, and ease of use of this little range finder. The serial interface is a bit odd (it's RS232 instead of standard TTL), but the PWM and Analog interfaces will allow any micro to listen easily enough. The sensor provides very accurate readings of 0 to 255 inches (0 to 6.45m) in 1 inch increments with little or no dead zone! Maxbotix is offering the EZ0, EZ1, EZ2, EZ3, and EZ4 with...

This is the fantastically easy to use sensor from Maxbotix. We are extremely pleased with the size, quality, and ease of use of this little range finder. The serial interface is a bit odd (it's...

This is the fantastically easy to use sensor from Maxbotix. We are extremely pleased with the size, quality, and ease of use of this little range finder. The serial interface is a bit odd (it's RS232 instead of standard TTL), but the PWM and Analog interfaces will allow any micro to listen easily enough. The sensor provides very accurate readings of 0 to 255 inches (0 to 6.45m) in 1 inch increments with little or no dead zone! Maxbotix is offering the EZ0, EZ1, EZ2, EZ3, and EZ4 with...

USB Weather Board Description: Got weather? This board can handle it. The USB Weather Board includes onboard sensors for barometric pressure, humidity, temperature, and light level....

USB Weather Board Description: Got weather? This board can handle it. The USB Weather Board includes onboard sensors for barometric pressure, humidity, temperature, and light level. We've also added headers in the new version so you can connect the board to our weather meters (not included), adding sensors for wind speed, wind direction, and rainfall. You can send all this data to a computer or datalogger via mini-USB cable, TTL serial (3.3V), or wirelessly...

Most ultrasonic distance sensors aren't waterproof which can be a problem if you need your project to withstand the elements outdoors. No need to worry any more! We have developed waterproof...

Most ultrasonic distance sensors aren't waterproof which can be a problem if you need your project to withstand the elements outdoors. No need to worry any more! We have developed waterproof ultrasonic distance sensors with a waterproof sealed emitter. This sensor is suitable for outdoor applications such as car reversing sensors, security alarms, industrial inspection, etc. What will you make? |Specification| Operating voltage: DC5V Static current: 5mA Operating current: 30mA Operating range:...

WS2801 Breakout Description: This is a breakout board for the WS2801 RGB LED controller, the same IC used in our addressable RGB LED strips. The board comes with the chip on one side and an RGB...

WS2801 Breakout Description: This is a breakout board for the WS2801 RGB LED controller, the same IC used in our addressable RGB LED strips. The board comes with the chip on one side and an RGB LED on the other. Several of these breakouts can be chained together to form a display or an addressable string. Voltage, ground, clock and data are broken out as input on one side and output on the other to standard 0.1" spaced headers. Documents: Schematic Eagle Files Datasheet (WS2801)...