Shop All

This is a very simple but extremely handy, 1" square, single sided perf board. Standard 0.1" spacing with a 4-40 (3mm) hole for mounting. Every three holes are connected with a 20mil trace. **...

This is a very simple but extremely handy, 1" square, single sided perf board. Standard 0.1" spacing with a 4-40 (3mm) hole for mounting. Every three holes are connected with a 20mil trace. ** Package of 2**

Overview PTFE Coupler is the anchor on the rear of the printer for fixing the PTFE tube. Installation Learn more about the replacement of the PTFE Coupler for P1 Series on Bambu Lab Wiki. In the Box...

Overview PTFE Coupler is the anchor on the rear of the printer for fixing the PTFE tube. Installation Learn more about the replacement of the PTFE Coupler for P1 Series on Bambu Lab Wiki. In the Box - PTFE Coupler*1 Compatibility P1 Series Exclusive

PTFE Coupler Ring to Prevent Back Flow of Filament into the Heater Block. Please note this is only compatible with Intergrated Heater Block + Nozzle and not Compatible with Olssen Block. Therefore...

PTFE Coupler Ring to Prevent Back Flow of Filament into the Heater Block. Please note this is only compatible with Intergrated Heater Block + Nozzle and not Compatible with Olssen Block. Therefore you can only use this on the Ultimaker 2, Ultimaker 2 Extended machines only. If you have upgraded your Ultimaker 2 to a 2+ you can not use this part.

Overview The function of PTFE Tube is to reduce resistance and guide filament. The tube’s inner diameter is 2.5mm, and its outer diameter is 4mm. Please note that the PTFE tubes are consumables and...

Overview The function of PTFE Tube is to reduce resistance and guide filament. The tube’s inner diameter is 2.5mm, and its outer diameter is 4mm. Please note that the PTFE tubes are consumables and are at risk of wear, as they may rub against the filament over time. We recommend that you check the PTFE tubes for wear during your maintenance of the machine. If the tubes are worn and not replaced in time, this may lead to feeding failures, filament accumulation inside the AMS, etc.   In the...

OverviewThe A1 PTFE Tube Connector used in A1 is attached to the X-axis motor housing and can be removed together with the pneumatic connector.CompatibilityA1 ExclusiveIn the BoxPTFE Tube Connector...

OverviewThe A1 PTFE Tube Connector used in A1 is attached to the X-axis motor housing and can be removed together with the pneumatic connector.CompatibilityA1 ExclusiveIn the BoxPTFE Tube Connector *1InstallationLearn more about replacing the PTFE Tube Connector - A1 on Bambu Lab Wiki.Product SpecificationMaterialsPlasticPackage Weight0.04 kgPackage Size60*60*30 mmColorWhite ...

Overview The PTFE Tube Connector is a component used to connect the PTFE tube, which is mounted on the back of the printer and used to connect the PTFE tube between the buffer and the tool head....

Overview The PTFE Tube Connector is a component used to connect the PTFE tube, which is mounted on the back of the printer and used to connect the PTFE tube between the buffer and the tool head. Compatibility X1 Series and P1 Series Instructions for use 1. The PTFE Tube Connector is designed with a clear direction of use, as shown in the figure below. Connect the PTFE tube from the buffer output to the IN end, and the PTFE tube from the tool head to the OUT end. It is important to note that...

Overview An assembly that installed on the back of the printer and it is used to clean the nozzle and slide the excess filament out of the printer. Installation Learn more about the replacement of...

Overview An assembly that installed on the back of the printer and it is used to clean the nozzle and slide the excess filament out of the printer. Installation Learn more about the replacement of the Purge Chute on Bambu Lab Wiki. In the Box - Purge Chute*1 Compatibility P1 Series and X1 Series

This Purge Wiper is designed to efficiently remove waste filament generated by the printer's hotend. It gathers and dislodges waste filament during different stages, including printer setup, pause...

This Purge Wiper is designed to efficiently remove waste filament generated by the printer's hotend. It gathers and dislodges waste filament during different stages, including printer setup, pause and resume operations, and filament changes for multi-color printing. Its purpose is to ensure the proper management and disposal of waste materials for seamless printing processes.Compatible with A1 Series.Learn more about the replacement of the Purge Wiper for A1 mini on Bambu Lab Wiki. ...

This high gain, 7.75" antenna is perfect for AVL applications where cellular reception is a must. Connector is regular SMA so don't confuse it with 2.4GHz antennas. Specifications: GSM/850E : 824 to...

This high gain, 7.75" antenna is perfect for AVL applications where cellular reception is a must. Connector is regular SMA so don't confuse it with 2.4GHz antennas. Specifications: GSM/850E : 824 to 894MHz GSM : 880 to 960MHz DCS : 1710 to 1880MHz PCS : 1850 to 1990MHz Documents: Datasheet

This is a fantastic find for SFE. A small, high-quality, quad-band, standard SMA terminated, cellular antenna. Specifications: GSM/850E : 824 to 894MHz GSM : 880 to 960MHz DCS : 1710 to 1880MHz PCS...

This is a fantastic find for SFE. A small, high-quality, quad-band, standard SMA terminated, cellular antenna. Specifications: GSM/850E : 824 to 894MHz GSM : 880 to 960MHz DCS : 1710 to 1880MHz PCS : 1850 to 1990MHz Documents: GSM Antenna 850-1900MHz

Quadstepper Motor Driver Board Description: The Quadstepper motor driver board allows you to control up to 4 bipolar stepper motors simultaneously using logic level IO pins. Each motor driver has an...

Quadstepper Motor Driver Board Description: The Quadstepper motor driver board allows you to control up to 4 bipolar stepper motors simultaneously using logic level IO pins. Each motor driver has an output drive capacity of 35V and 1Amps. The board is capable of driving motors in full, half, quarter, eight, and sixteenth-step modes. The logic levels are selectable between 3.3V and 5V by way of a jumper. The bus header allows you to control all four motors with only 6 IO pins by...

Quick Disconnect - Female 1/5 (bag of 50) Description: These connectors are really useful as power connectors in prototyping or in projects that are repeatedly assembled and disassembled. There are...

Quick Disconnect - Female 1/5 (bag of 50) Description: These connectors are really useful as power connectors in prototyping or in projects that are repeatedly assembled and disassembled. There are also a variety of buttons and lights that use these standard connectors. These Female quick-disconnects are about 1/5" wide and can be crimped onto 16-14 AWG wire. Mating connectors can be found in the related items. Documents: Datasheet " ...

"These connectors are really useful as power connectors in prototyping or in projects that are repeatedly assembled and disassembled. There are also a variety of buttons and lights that use these...

"These connectors are really useful as power connectors in prototyping or in projects that are repeatedly assembled and disassembled. There are also a variety of buttons and lights that use these standard connectors. These Female quick-disconnects are about ¼" wide and can be crimped onto 16-14 AWG wire. Mating connectors can be found in the related items. Documents: Datasheet " ...

"These connectors are really useful as power connectors in prototyping or in projects that are repeatedly assembled and disassembled. There are also a variety of buttons and lights that use these...

"These connectors are really useful as power connectors in prototyping or in projects that are repeatedly assembled and disassembled. There are also a variety of buttons and lights that use these standard connectors. These Male quick-disconnects are about ¼" wide and can be crimped onto 22-16 AWG wire. Mating connectors can be found in the related items. Documents: Datasheet " ...

"These connectors are really useful as power connectors in prototyping or in projects that are repeatedly assembled and disassembled. There are also a variety of buttons and lights that use these...

"These connectors are really useful as power connectors in prototyping or in projects that are repeatedly assembled and disassembled. There are also a variety of buttons and lights that use these standard connectors. These Male quick-disconnects are about 1/5" wide and can be crimped onto 22-16 AWG wire. Mating connectors can be found in the related items. Documents: Datasheet " ...

Here is a tiny 4-pin Qwiic 1mm JST connector. This connector is used on all of our Qwiic-based boards and can be used to create your own I2C-based device compatible with the Qwiic system....

Here is a tiny 4-pin Qwiic 1mm JST connector. This connector is used on all of our Qwiic-based boards and can be used to create your own I2C-based device compatible with the Qwiic system. Additionally, this connector will mate with all of our Qwiic cables with a solid lock. The SparkFun Qwiic connect system is an ecosystem of I2C sensors, actuators, shields and cables that make prototyping faster and less prone to error. All Qwiic-enabled boards use a common 1mm pitch, 4-pin JST connector....

The Raspberry Pi is THE new favorite of development platforms, so the last thing that you’d want is for something bad to happen to it. Why not protect it with one of these snazzy clear plastic...

The Raspberry Pi is THE new favorite of development platforms, so the last thing that you’d want is for something bad to happen to it. Why not protect it with one of these snazzy clear plastic enclosures? These clear cases protect the Raspberry Pi 3, RPi2, and Model B+ from things like rogue wires that might short it out while still allowing full access to the board as well as proper airflow to keep your new toy cool! Simply snap the RPi into the bottom half of the enclosure, then snap the two...

The Raspberry Pi 400 is a complete Raspberry Pi 4-based personal computer, integrated into a keyboard. By incorporating the board into a keyboard, it removes the need for a case and other...

The Raspberry Pi 400 is a complete Raspberry Pi 4-based personal computer, integrated into a keyboard. By incorporating the board into a keyboard, it removes the need for a case and other accessories normally needed to run a Raspberry and creates a more clean configuration. It makes for the perfect configuration for a public machine or in an educational setting including the incorporation of a Kensington lock (Locking port used on laptops for security in public spaces). The Raspberry Pi 400...

The Raspberry Pi Active Cooler provides an alternative cooling solution for users who wish to use their Raspberry Pi 5 under sustained heavy load without a case. It combines a large metal heatsink...

The Raspberry Pi Active Cooler provides an alternative cooling solution for users who wish to use their Raspberry Pi 5 under sustained heavy load without a case. It combines a large metal heatsink with a variable-speed blower, again powered and controlled via the fan connector, and attaches to the Raspberry Pi 5 PCB via sprung pins into a pair of mounting holes. Features: A single-piece anodized aluminium heatsink Heatsink-mounted, temperature-controlled fan 5V blower fan with max speed of...

This 8mp camera module is capable of 1080p video and still images that connect directly to your Raspberry Pi. This is the plug-and-play-compatible latest version of the Raspbian operating system,...

This 8mp camera module is capable of 1080p video and still images that connect directly to your Raspberry Pi. This is the plug-and-play-compatible latest version of the Raspbian operating system, making it perfect for time-lapse photography, recording video, motion detection and security applications. Connect the included ribbon cable to the CSI (Camera Serial Interface) port on your Raspberry Pi, and you are good to go! The board itself is tiny, at around 25mm x 23mm x 9mm and weighing in at...

"The Raspberry Pi is THE new favorite of development platforms, so the last thing that you’d want is for something bad to happen to it. Why not protect it with one of these snazzy black...

"The Raspberry Pi is THE new favorite of development platforms, so the last thing that you’d want is for something bad to happen to it. Why not protect it with one of these snazzy black plastic enclosures? These cases protect the RPi2 and Model B+ from things like rogue wires that might short it out while still allowing full access to the board as well as proper airflow to keep your new toy cool! Simply snap the RPi into the bottom half of the enclosure, then snap the two sides together....

This 2x20 male header has the same number and spacing of pins as a Raspberry Pi but is best served when used in conjunction with the Pi Zero since they come with a space of unpopulated headers. This...

This 2x20 male header has the same number and spacing of pins as a Raspberry Pi but is best served when used in conjunction with the Pi Zero since they come with a space of unpopulated headers. This through-hole header has 40 0.1"-spaced pins and can just be snapped into place with minimal soldering! Documents: Dimensional Drawing

This 2x20 shrouded header has the same number and spacing of pins as a Raspberry Pi so you can easily connect via ribbon cable to the low-level peripherals and get hacking! This through-hole header...

This 2x20 shrouded header has the same number and spacing of pins as a Raspberry Pi so you can easily connect via ribbon cable to the low-level peripherals and get hacking! This through-hole header has 40 0.1"-spaced pins and is keyed for polarity. Check the related items below for the mating cable! Documents: Datasheet Videos ...

The Raspberry Pi Micro USB to USB-C Adapter is a small adapter that allows a male Micro-B USB power adapter the ability to power devices with a female USB Type C port, specifically the Raspberry Pi...

The Raspberry Pi Micro USB to USB-C Adapter is a small adapter that allows a male Micro-B USB power adapter the ability to power devices with a female USB Type C port, specifically the Raspberry Pi 4. This adapter is perfect for those looking to power their Raspberry Pi 4 with their power supply from the Raspberry Pi 3 line. Features: USB Micro B Female port USB Type C Male Port 15mm overhang when connected to your Raspberry Pi ...

Raspberry PI nRF24 Add-on for Raspberry PI platform. Integrated on-chip transceiver nRF24L01 + PA and LNA allows you to create a wireless connection between the terminal devices (sensors, etc.) and...

Raspberry PI nRF24 Add-on for Raspberry PI platform. Integrated on-chip transceiver nRF24L01 + PA and LNA allows you to create a wireless connection between the terminal devices (sensors, etc.) and servers. The Raspberry PI nRF24 Add-on added all the ingredients needed to make Raspberry PI in a completely finished and inexpensive gateway to build a heterogeneous environment for the smart home. Many Open Source controllers and accessible library will allow you to create any kind of smart,...

Raspberry Pi Zero is a a super-small, hackable, and ultra-low-cost computer. It is half of the size of a Model A+, with twice the utility. It just looks like a slimmed down version of the Raspberry...

Raspberry Pi Zero is a a super-small, hackable, and ultra-low-cost computer. It is half of the size of a Model A+, with twice the utility. It just looks like a slimmed down version of the Raspberry Pi we know and love. It's kind of like the little brother to the Pi 2 - with just a micro SD card slot, a mini HDMI port, two micro USB ports (one for power, one for USB), and 512MB of RAM. It has a single-core 1 GHz processor chip, similar to the Pi A+ and B+. Actually it’s 40% faster than the...

The Raspberry Pi Zero Case has been designed to fit both the Pi Zero and the Pi Zero W. These official cases consist of several parts and protect the Raspberry Pi Zero from things like rogue wires...

The Raspberry Pi Zero Case has been designed to fit both the Pi Zero and the Pi Zero W. These official cases consist of several parts and protect the Raspberry Pi Zero from things like rogue wires that might short it out while still allowing full access to the board. Simply snap the RPi into the bottom half of the enclosure, then snap on a desired top. No tools required! Each case has a standard base featuring a cut-out to allow access to the GPIO, and a choice of three lids: a standard lid, a...

The credit-card-sized computer has become even smaller! The Raspberry Pi Zero W is still the Pi you know and love, but at a largely reduced size of only 65mm long by 30mm wide and now with headers!...

The credit-card-sized computer has become even smaller! The Raspberry Pi Zero W is still the Pi you know and love, but at a largely reduced size of only 65mm long by 30mm wide and now with headers! With the addition of wireless LAN and Bluetooth, the Raspberry Pi Zero W is ideal for making embedded Internet of Things (IoT) projects. The Pi Zero W has been designed to be as flexible and compact as possible with mini connectors and a populated 40-pin GPIO. At the heart of the Raspberry Pi Zero W...

RaspiRobot Board Description: The Raspberry Pi packs plenty of processing power in a small and inexpensive package and that makes it perfect for robot brains! The only problem? The Raspberry Pi may...

RaspiRobot Board Description: The Raspberry Pi packs plenty of processing power in a small and inexpensive package and that makes it perfect for robot brains! The only problem? The Raspberry Pi may have plenty of low-level hardware peripherals but motor controllers aren't one of them. That's why the RaspiRobot project got started. The RaspiRobot board is an expansion board for the Pi that turns it into a robot controller. The board comes as a kit of through-hole parts which is easy to...

    John Jay based in Georgia, USA, is a retired engineer who designed some boards for the Raspberry Pi to help his partner to learn Raspberry Pi. Although at first it was a...

    John Jay based in Georgia, USA, is a retired engineer who designed some boards for the Raspberry Pi to help his partner to learn Raspberry Pi. Although at first it was a small act that just for his friends, but with the growing people in the open-source community participating, more and more people find that these packages really works. So, he decided to releases these kits. Cooperated with Elecrow, these packages have been produced quickly. And here with Elecrow, we...

Overview It is the black metal panel that is installed on the back of the P1S printer (Please use the original screws from the printer for black metal rear pannel installation, as there are no...

Overview It is the black metal panel that is installed on the back of the P1S printer (Please use the original screws from the printer for black metal rear pannel installation, as there are no screws included in the package of this spare part). Installation Learn more about the replacement of the Rear Metal Panel for P1 Series on Bambu Lab Wiki. In the Box - Rear Metal Panel*1 ...

This is a small device called a reed switch. When the device is exposed to a magnetic field, the two ferrous materials inside the switch pull together and the switch closes. When the magnetic field...

This is a small device called a reed switch. When the device is exposed to a magnetic field, the two ferrous materials inside the switch pull together and the switch closes. When the magnetic field is removed, the reeds separate and the switch opens. This makes for a great non-contact switch. This switch can carry up to 1.2A. Documents: Datasheet Hookup Guide Application Note Videos ...

This Relay Shield v2.0 from Evil Mad Scientist is a simple Arduino add-on that gives your Arduino the ability to control a single electromechanical relay for switching loads of up to 24VDC or 40VAC....

This Relay Shield v2.0 from Evil Mad Scientist is a simple Arduino add-on that gives your Arduino the ability to control a single electromechanical relay for switching loads of up to 24VDC or 40VAC. Each Relay Shield comes equipped with a single pole - double throw (SPDT) sealed relay which can handle a current load of up to 5A. This means that when current is applied to the coil it throws a simple changeover switch, terminating the connection from the NC (Normally Closed) contact to ground...

These are high quality Single Pole - Double Throw (SPDT) sealed relays. Use them to switch high voltage, and/or high current devices. This relay's coil is rated up to 12V, with a minimum switching...

These are high quality Single Pole - Double Throw (SPDT) sealed relays. Use them to switch high voltage, and/or high current devices. This relay's coil is rated up to 12V, with a minimum switching voltage of 5V. The contacts are rated up to 5A (@250VAC, 30VDC). Note: In the Datasheet below there is a pin layout listed as "Bottom View." Be aware, this pin layout is actually the top-down view NOT bottom-up. Features: 5V DC SPDT Relay Rated up to 5A Fully Sealed Documents: Datasheet ...

These are massive single pole - double throw (SPDT) sealed relays. This means that when current is applied to the coil it throws a simple changeover switch, terminating the connection from the NC...

These are massive single pole - double throw (SPDT) sealed relays. This means that when current is applied to the coil it throws a simple changeover switch, terminating the connection from the NC contact to ground and closing the NO contact. Use them to switch high voltage/high current devices. Features: SPDT Relay Contacts Rated up to 220VAC @ 20A Coil Voltage: 5V Fully Sealed Documents: Datasheet (JQX-15F/005) Relay Tutorial ...

Overview The filament can be cut to prevent the supplies from clogging. When used with AMS, it assists with multi-material switching. Compatibility X1 Series, P1 Series, A1 Series Installation Learn...

Overview The filament can be cut to prevent the supplies from clogging. When used with AMS, it assists with multi-material switching. Compatibility X1 Series, P1 Series, A1 Series Installation Learn more about the replacement of the filament cutter on Bambu Lab Wiki: X1 Series and P1 Series, A1 Series. ...

Overview The filament can be cut to prevent the supplies from clogging. When used with AMS, it assists with multi-material switching. Compatibility X1 Series, P1 Series, A1 Series Installation Learn...

Overview The filament can be cut to prevent the supplies from clogging. When used with AMS, it assists with multi-material switching. Compatibility X1 Series, P1 Series, A1 Series Installation Learn more about the replacement of the filament cutter on Bambu Lab Wiki: X1 Series and P1 Series, A1 Series. ...

1/6th Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and perf boards, these 1.0M resistors make excellent pull-ups, pull-downs, and current limiters. Note: Although these come in...

1/6th Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and perf boards, these 1.0M resistors make excellent pull-ups, pull-downs, and current limiters. Note: Although these come in bags marked with a quantity of 25, they don't always contain 25. So we'd rather call it 20 and hope that you get extras. Documents: Breadboard Lecture Sensor Interfacing Voltage Dividers ...

Resistors are a good thing, in fact, they're actually crucial in a lot of circuit designs. The only problem seems to be that resistors disappear into thin air. The only way to be sure that you're...

Resistors are a good thing, in fact, they're actually crucial in a lot of circuit designs. The only problem seems to be that resistors disappear into thin air. The only way to be sure that you're gonna have the resistor you need when you need it is to stock up, and keep them organized. We have just the thing! Our new branded resistor kit comes with 25 each of 20 different resistor values (including 0Ω links!). All of these resistors are stapled into a tri-fold pack and clearly labeled. The...

These are your standard issue USB 2.0 type A to micro USB 5-pin... but wait, what's this? These cables have minor, yet genius modifications that allow both ends to be plugged into their ports...

These are your standard issue USB 2.0 type A to micro USB 5-pin... but wait, what's this? These cables have minor, yet genius modifications that allow both ends to be plugged into their ports regardless of their orientation. No longer will you fight the USB "super position" where both orientations of your plug seem incorrect. A simple solution to a problem that nearly everyone has faced. This is one of the features we love so much about USB-C, but now it works with all your Micro-B devices as...

These wireless receivers work with our 434MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only...

These wireless receivers work with our 434MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only receivers, they will only work communicating data one-way, you would need two pairs (of different frequencies) to act as a transmitter/receiver pair. Note: These modules are indiscriminate and will receive a fair amount of noise. Both the transmitter and receiver work at common frequencies and...

These wireless transmitters work with our 434MHz receivers. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only...

These wireless transmitters work with our 434MHz receivers. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of different frequencies) to act as a transmitter/receiver pair. Note: These modules are indiscriminate and will receive a fair amount of noise. Both the transmitter and receiver work at common frequencies and...

RFID (radio-frequency identification) is the wireless non-contact use of radio-frequency electromagnetic fields, for the purposes of identifying and tracking tags attached to objects. This is the...

RFID (radio-frequency identification) is the wireless non-contact use of radio-frequency electromagnetic fields, for the purposes of identifying and tracking tags attached to objects. This is the ID-12LA, a very simple to use RFID reader module from ID Innovations. With a built in antenna, the only holdup is the 2mm pin spacing. Power the module, hold up a 125kHz card, and get a serial string output containing the unique ID of the card. Note: The new ID-12LA is essentially the same as the...

You might know RFID as the technology that Big Brother uses to track your every move. Quickly, don the tinfoil hats!! Only kidding. RFID is useful for sensing and identifying tagged people and...

You might know RFID as the technology that Big Brother uses to track your every move. Quickly, don the tinfoil hats!! Only kidding. RFID is useful for sensing and identifying tagged people and objects for access control, automation and a whole range of different applications. This basic RFID tag works in the 125kHz RF range and comes with a unique 40-bit ID. It is not reprogrammable. This blank, smooth, mildly flexible RFID tag is ready for your logo (or hand-drawn scribble). Features: EM4001...

This is the 915MHz base RFM69HCW Wireless Transceiver that is found on our RFM69 Breakout. The RFM69HCW is an inexpensive and versatile radio module that operates in the unlicensed ISM (Industry,...

This is the 915MHz base RFM69HCW Wireless Transceiver that is found on our RFM69 Breakout. The RFM69HCW is an inexpensive and versatile radio module that operates in the unlicensed ISM (Industry, Science and Medicine) band, a set of frequencies set aside for low-power, short-range, license-free radios. It’s perfect for building inexpensive short-range wireless networks of sensors and actuators for home automation, citizen science and more. This RFM69HCW module operates on the 915MHz frequency...

Ribbon cable is really helpful in situations where you need to make a lot of connections without a big mess of wires. Nothing makes a project look more finished than a nice clean wiring harness....

Ribbon cable is really helpful in situations where you need to make a lot of connections without a big mess of wires. Nothing makes a project look more finished than a nice clean wiring harness. This is a 15ft. length of 10-wire ribbon cable. Check the related products below for crimp-on connectors that will fit this cable. Documents: [Datasheet](http://cdn.sparkfun.com/datasheets/Cables/HookUp/Morethanall IDC Cable HFR-28R3HF-xx.pdf) ...

"This ZIF connector mates with the 6-conductor ribbon cable for the GP-2106 GPS module. Use it to roll your own GP-2106 carrier board! Documents: Datasheet (FH34SRJ-6S-0.5SH) " ...

"This ZIF connector mates with the 6-conductor ribbon cable for the GP-2106 GPS module. Use it to roll your own GP-2106 carrier board! Documents: Datasheet (FH34SRJ-6S-0.5SH) "

Overview It is the plastic panel that is installed on the right side of the printer when facing the screen of the printer. Installation Learn more about the replacement of the Right Plastic Panel...

Overview It is the plastic panel that is installed on the right side of the printer when facing the screen of the printer. Installation Learn more about the replacement of the Right Plastic Panel for P1 Series on Bambu Lab Wiki. Please note that the left and right side panels of the P1P may be incompatible with the base and require shaving off two tabs on the bottom of side panels for successful installation. Two types of bases for the P1P model We have two types of bases for the P1P model....

These are simple through-hole RJ45 sockets with PCB mounting posts. These 8-pin connectors are commonly used in conjunction with Cat5, Cat5e, and Cat6 Ethernet cables. Because Ethernet cable is so...

These are simple through-hole RJ45 sockets with PCB mounting posts. These 8-pin connectors are commonly used in conjunction with Cat5, Cat5e, and Cat6 Ethernet cables. Because Ethernet cable is so ubiquitous, these are awesome for projects where you need to string a lot of modules together over a distance. We used these, along with the breakout boards which you can find in the related items below, in the Sound Squid demo! Note: The price listed is for one jack. Documents: Datasheet ...

"The RN-XV module by Roving Networks is a certified Wi-Fi solution especially designed for customer who want to migrate their existing 802.15.4 architecture to a standard TCP/IP based platform...

"The RN-XV module by Roving Networks is a certified Wi-Fi solution especially designed for customer who want to migrate their existing 802.15.4 architecture to a standard TCP/IP based platform without having to redesign their existing hardware. In other words, if your project is set up for XBee and you want to move it to a standard WiFi network, you can drop this in the same socket without any other new hardware. The RN-XV module is based upon Roving Networks' robust RN-171 Wi-Fi module and...

These panel-mounting rocker switches have built-in indicator lights to let you know when your switch is engaged. They mount into a 20.2mm diameter hole and are rated up to 16A @ 12v. These simple...

These panel-mounting rocker switches have built-in indicator lights to let you know when your switch is engaged. They mount into a 20.2mm diameter hole and are rated up to 16A @ 12v. These simple SPST on-off switches have three terminals, the two that you would normally see plus a ground tab for the blue LED lamp inside. Although these are rated for 12v, the LED works with as little as 5V. Features: Blue LED Indicator SPST on-off Rated up to 16A @ 12v 20.2mm Diameter Mounting Hole Videos ...

This little round on/off toggle switch is rated up to 10A at 125VAC and can be panel mounted in a 20mm diameter hole. It'll also look pretty slick in your project. Documents: Dimensional Drawing ...

This little round on/off toggle switch is rated up to 10A at 125VAC and can be panel mounted in a 20mm diameter hole. It'll also look pretty slick in your project. Documents: Dimensional Drawing

This is a 12-step rotary encoder with a nice 'clicking' feel. It's breadboard friendly, and has a pretty handy select switch (by pushing in on the knob). The encoder is different from a...

This is a 12-step rotary encoder with a nice 'clicking' feel. It's breadboard friendly, and has a pretty handy select switch (by pushing in on the knob). The encoder is different from a potentiometer in that an encoder has full rotation without limits. The unit outputs gray code so that you can tell how much and in which direction the encoder has been turned. This unit does not come with a knob, but a working knob is related below. Documents: Bildr example showing how to use an encoder in...

This bundle includes the following items. 3 epoxy tooling material (rotary CNC) and 3 kraft cylinder (rotary laser) ...

This bundle includes the following items. 3 epoxy tooling material (rotary CNC) and 3 kraft cylinder (rotary laser)

An adjustable potentiometer can open up many interesting user interfaces. Turn the pot and the resistance changes. Connect VCC to an outer pin, GND to the other, and the center pin will have a...

An adjustable potentiometer can open up many interesting user interfaces. Turn the pot and the resistance changes. Connect VCC to an outer pin, GND to the other, and the center pin will have a voltage that varies from 0 to VCC depending on the rotation of the pot. Hook the center pin to an ADC on a microcontroller and get a variable input from the user! This pot has a 1/4" mounting diameter and has a 10K linear taper. Check the datasheet for dimensional drawings. Documents: Datasheet How...

An adjustable potentiometer can open up many interesting user interfaces. Turn the pot and the resistance changes. Connect VCC to an outer pin, GND to the other, and the center pin will have a...

An adjustable potentiometer can open up many interesting user interfaces. Turn the pot and the resistance changes. Connect VCC to an outer pin, GND to the other, and the center pin will have a voltage that varies from 0 to VCC depending on the rotation of the pot. Hook the center pin to an ADC on a microcontroller and get a variable input from the user! This is a center-tap linear type potentiometer. The outer two pins will always show 10K resistance, the center pin resistance to one of the...

This is a single pole, 10 position rotary switch able to select up to 10 different states in a durable package. Unlike our other rotary switch, this model is much more robust and capable of handling...

This is a single pole, 10 position rotary switch able to select up to 10 different states in a durable package. Unlike our other rotary switch, this model is much more robust and capable of handling larger currents and voltages. You may find this rotary switch familiar, it's the same one we trusted in our Decade Resistance Box! With a max voltage rating of 125VAC at 0.3A and a dielectric strength of 250VAC for 1 minute this is a serious little rotary switch capable of working with some of your...

Schottky diodes are known for their low forward voltage drop and a very fast switching action. This 1A 40V Schottky diode is ideal for use with motor drivers such as the L298N. Documents: Datasheet ...

Schottky diodes are known for their low forward voltage drop and a very fast switching action. This 1A 40V Schottky diode is ideal for use with motor drivers such as the L298N. Documents: Datasheet

These are simple 2-position screw terminals with 2.54mm pitch pins. Rated up to 150V @ 6A, this terminal can accept 30 to 18AWG wire. The 2.54mm pitch will line up with standard 0.1" perf boards....

These are simple 2-position screw terminals with 2.54mm pitch pins. Rated up to 150V @ 6A, this terminal can accept 30 to 18AWG wire. The 2.54mm pitch will line up with standard 0.1" perf boards. Documents: Datasheet

Screw Terminals with 3.5mm pitch pins. Comes in 2, 3, or 4 positions and have the really cool feature of slide-locking together to form any size you need (4, 5, up to 20 without problems). Rated up...

Screw Terminals with 3.5mm pitch pins. Comes in 2, 3, or 4 positions and have the really cool feature of slide-locking together to form any size you need (4, 5, up to 20 without problems). Rated up to 125V @ 10A. Terminal can accept 16 to 26AWG wire. 3.5mm/138mil pin pitch will not fit standard 0.1" perf boards but this is the most common pitch screw terminal. Documents: Datasheet ...

    This is a 3 Pole 5.0mm Screw Terminal Block.It includes 5 units of Terminal Block.There are screws which are tightened for a secure connection for both lugs and bare wire....

    This is a 3 Pole 5.0mm Screw Terminal Block.It includes 5 units of Terminal Block.There are screws which are tightened for a secure connection for both lugs and bare wire. Specification Rated: 250,16A(250V,17.5A)Contact resistance: 200m? MaxInsulation resistance: 5000M? MinTemp range: -30?~+120?Max Soldering: +260? 5sWire range: 22-14AWG(1.5mm2)Strip length: 3.5mm      ...

The 4x4 Keypad is a general purpose 16 button (4x4) matrix keypad. It comes ready to work, simply peel-off the adhesive backing, stick it to your surface and plug it in. ...

The 4x4 Keypad is a general purpose 16 button (4x4) matrix keypad. It comes ready to work, simply peel-off the adhesive backing, stick it to your surface and plug it in.

This is your simple three conductor sensor cable with electrode pad leads. These cables are 24" long and feature a 3.5mm audio jack connector on one end with snap style receptacles for biomedical...

This is your simple three conductor sensor cable with electrode pad leads. These cables are 24" long and feature a 3.5mm audio jack connector on one end with snap style receptacles for biomedical sensor pads. Each cable comes in a red/blue/black set. Features: 24" Long 4 mm connector Documents: Product Video

    Arduino Sensor Shield V4.0 let us to build electronics projects just as easy as piling bricks. It can connect to various modules like sensors, servos, relays, buttons,...

    Arduino Sensor Shield V4.0 let us to build electronics projects just as easy as piling bricks. It can connect to various modules like sensors, servos, relays, buttons, potentiometers. Just plug & play.     Each functional module has buckled port with VCC, GND and Output, which has corresponding port on the Sensor Shield, connected with a plain 2.54mm dual-female cable you may start playing already. Buckled brick cables are like cement for bricks,...