Electronic Components

Your basic 7-segment LED, but in blue! Common anode. Two decimal points, but only the one on the right is wired. Digit height is 0.6". Overall height is 1". Check out this tutorial on how to use...

Your basic 7-segment LED, but in blue! Common anode. Two decimal points, but only the one on the right is wired. Digit height is 0.6". Overall height is 1". Check out this tutorial on how to use this product with the 74HC595 Shift Register and Arduino. Thanks Patrick and Mycha! Documents: Datasheet Arduino Library (Thanks Derek!) ...

9 Degrees of Freedom - MPU-9150 Breakout Description: The MPU-9150 is the world’s first 9-axis MotionTracking device designed for the low power, low cost, and high performance...

9 Degrees of Freedom - MPU-9150 Breakout Description: The MPU-9150 is the world’s first 9-axis MotionTracking device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it. This breakout board makes it easy to prototype with the InvenSense MPU-9150 by breaking out all the pins you need to standard 0.1" spaced headers. The board...

A small 1/4 wave rubber duck antenna for LoRa or other 860-960MHz communication. Antenna has a center frequency of 915MHz and utilizes an RP-SMA connector. Gain is 2dBi with an overall length of...

A small 1/4 wave rubber duck antenna for LoRa or other 860-960MHz communication. Antenna has a center frequency of 915MHz and utilizes an RP-SMA connector. Gain is 2dBi with an overall length of 110mm.

    This is 200mm long 9pin female to female jumper wire which uses high quality 26# line. Great for jumping from board to board. These are simple jumper wires used on standard...

    This is 200mm long 9pin female to female jumper wire which uses high quality 26# line. Great for jumping from board to board. These are simple jumper wires used on standard 2.54mm(0.1") breakaway headers.

Classic 9V snap connector terminated with 2-pin polarized Molex connector with 0.1" spacing. The cable is 26AWG and is 5" in length.

Classic 9V snap connector terminated with 2-pin polarized Molex connector with 0.1" spacing. The cable is 26AWG and is 5" in length.

This simple cable has so many uses! Plug the 9 volt battery clip onto a standard 9V battery and connect the other end to anything with a 5.5x2.1mm, center-positive barrel jack. Use this cable to...

This simple cable has so many uses! Plug the 9 volt battery clip onto a standard 9V battery and connect the other end to anything with a 5.5x2.1mm, center-positive barrel jack. Use this cable to battery-power any device that needs 9V and has an on-board barrel jack - it works great for Arduinos, development boards, evaluation boards, and more! ...

This is the second version of the 9V to Barrel Jack Adapter. In this version the material for the 9V battery jack is hard plastic, which makes it easier to connect and disconnect You can plug a 9V...

This is the second version of the 9V to Barrel Jack Adapter. In this version the material for the 9V battery jack is hard plastic, which makes it easier to connect and disconnect You can plug a 9V battery into one end and connect the other end to anything with a 5.5x2.1mm, center-positive barrel jack. Use this cable to battery-power any device that needs 9V and has an on-board barrel jack - it works great for Arduinos, development boards, evaluation boards and more! |ShippingList| 9V to Barrel...

Keep your Raspberry Pi computer safe and sound in this lovely clear acrylic enclosure. This enclosure is special designed for the Raspberry Pi Model B+. It comes as 6 pieces of acrylic boards and...

Keep your Raspberry Pi computer safe and sound in this lovely clear acrylic enclosure. This enclosure is special designed for the Raspberry Pi Model B+. It comes as 6 pieces of acrylic boards and some other modules such DC fan, heat sink and even screwdriver, to help user better experience with the Raspberry Pi Model B+.     This ingenious design has no screws or standoffs and there are cute little feet cut into the sides so that it stands up above your desk. There are...

ADH8066 Evaluation Board Description: The evaluation board for the ADH8066 Cell Module breaks out all the pins to the module and provides you with the necessary support hardware to get you up and...

ADH8066 Evaluation Board Description: The evaluation board for the ADH8066 Cell Module breaks out all the pins to the module and provides you with the necessary support hardware to get you up and running. The ADH8066 board attaches to any USB port and appears as a standard com port. Power up the board with 6-12 VDC, turn on the module, and you can start sending and receiving AT commands via HyperTerminal or your favorite terminal program. The board comes assembled as shown so you don't...

    This is an infrared distance switch. It has an adjustable detection ranging from 3cm to 80cm. It is small, easy to use/assemble, and inexpensive. Useful for robotics,...

    This is an infrared distance switch. It has an adjustable detection ranging from 3cm to 80cm. It is small, easy to use/assemble, and inexpensive. Useful for robotics, interactive media, industrial assembly line, etc. Specification Power supply: 5V Current: 100mA Range: 3-80cm adjustable Red: +5V Yellow: Signal Black: GND Wire length: 20cm Wiki & External links Manual/Wiki ...

"This pack of 4-40 screws comes with a matching hex key. Each screw is 10mm in length. These are left over production stock from the original version of the BigTime Watch Kit so they won’t be...

"This pack of 4-40 screws comes with a matching hex key. Each screw is 10mm in length. These are left over production stock from the original version of the BigTime Watch Kit so they won’t be around for long. Includes: 4x screws 1x hex key Dimensions: 10mm long"

This is a 10-pack of wires that are pre-terminated with an alligator clip on one end and a female header on the other. Alligator clips are a staple item for any workbench or makerspace, and with...

This is a 10-pack of wires that are pre-terminated with an alligator clip on one end and a female header on the other. Alligator clips are a staple item for any workbench or makerspace, and with these cables you will be able to easily incorporate those clips into a breadboard, development platform or anything else to which you would normally be able to attach a hookup wire. Each alligator clip with female header cable has a wire length of 30cm (that's a little less than 1ft) and a port that...

"These Large Insulated Alligator Clips are great for clamping anything that you don’t want to deform yet large enough to easily manipulate. Thanks to the insulated flat surface, these clips...

"These Large Insulated Alligator Clips are great for clamping anything that you don’t want to deform yet large enough to easily manipulate. Thanks to the insulated flat surface, these clips can be used in a variety of applications such as, gripping small wires, coin cell battery, or large pads (like on our LilyPad boards). These clips offer an open clearance of a little over 8mm, two pan head screw terminals for wire connection, and a max current limit of 10A (theoretically). Sold in...

Alligator clips (or Crocodile clips, if you prefer) are likely to be the most useful thing on your workbench besides the workbench itself. Whether you're just trying to make a few quick connections...

Alligator clips (or Crocodile clips, if you prefer) are likely to be the most useful thing on your workbench besides the workbench itself. Whether you're just trying to make a few quick connections to test your circuit or having trouble making your multimeter leads stay where you need them, these spring-loaded clips are a workshop must-have. Each lead in this pack of tern is 50cm long with a rubber shrouded alligator clip on each end. There are five different colors, you get two each of: red,...

This is a heavy-duty joystick very similar to the ones in claw arcade games. Directional movements are momentary limit switches - one for each direction. This joystick also has a select button that...

This is a heavy-duty joystick very similar to the ones in claw arcade games. Directional movements are momentary limit switches - one for each direction. This joystick also has a select button that is actuated when the red button is pressed down. This joystick is pretty beefy and very tall because of it. We built up an enclosure just to see what it would look like. Ideally, this joystick would be panel mounted, but actually reading the movement of the joystick is as simple as setting up the...

4-way Pacman type arcade joystick. Heavy duty design gives this joystick a great feel! Features: ABS plastic and solid alloy construction Uses 4 microswitches to detect on/off position Unique handle...

4-way Pacman type arcade joystick. Heavy duty design gives this joystick a great feel! Features: ABS plastic and solid alloy construction Uses 4 microswitches to detect on/off position Unique handle design Spring return to center Very rugged construction Rated 5A @ 125V, 3A @ 250V* Overall height: 101mm Base: 97x65mm Joystick height: 60mm Documents: Manual ...

We've been prototyping for a long time on these awesome little plastic plates but it's time for an upgrade. This version still holds an Arduino and a self-adhesive clear breadboard but we've done...

We've been prototyping for a long time on these awesome little plastic plates but it's time for an upgrade. This version still holds an Arduino and a self-adhesive clear breadboard but we've done away with the plastic clips and now provide screws which give you a more solid and simple connection. Also, because the outside dimensions of the board don't matter anymore, this plate can be used with any board that has the Arduino mounting holes. The Arduino Uno, The Leonardo, FEZ Panda even the...

"The Arduino Industrial 101 is a WiFi evaluation board for the Arduino 101 LGA module based on a MIPS Linux processor. With the Industrial 101 you will possess a fantastic addition to the Arduino...

"The Arduino Industrial 101 is a WiFi evaluation board for the Arduino 101 LGA module based on a MIPS Linux processor. With the Industrial 101 you will possess a fantastic addition to the Arduino family and be able to easily create IoT projects without the need for multiple shields. Similar to the Arduino Yun (in a small form-factor), the Industrial 101 integrates an ATmega32U4 and the Atheros AR9331 SoC to make a dependable evaluation resource! The onboard ATmega32u4 microcontroller has been...

Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements the Processing/Wiring language. Arduino can be used to develop...

Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements the Processing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux). The Arduino Mega is a microcontroller board based on the ATmega2560. It has 54 digital input/output...

It's blue! It's skinny! It's the Arduino Pro! SparkFun's minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader. Because the system voltage for this board is lower...

It's blue! It's skinny! It's the Arduino Pro! SparkFun's minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader. Because the system voltage for this board is lower than other Arduino development boards, it may not be compatible with many Arduino shields which were designed to run at 5V. The Arduino Pro 3.3V still works great with our prototyping shield so you can create your own 3.3V shields. The lower system voltage also has its advantages, like ease of use...

It's blue! It's skinny! It's the Arduino Pro! SparkFun's minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader in a super-sleek form factor that will fit easily into...

It's blue! It's skinny! It's the Arduino Pro! SparkFun's minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader in a super-sleek form factor that will fit easily into your next small project. Arduino Pro does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommend first time Arduino users start with the Uno R3. It's a great board that will get you up and running quickly. The Arduino Pro series...

It's blue! It's thin! It's the Arduino Pro Mini! SparkFun's minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader. Arduino Pro Mini does not come with connectors...

It's blue! It's thin! It's the Arduino Pro Mini! SparkFun's minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader. Arduino Pro Mini does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommend first time Arduino users start with the Uno R3. It's a great board that will get you up and running quickly. The Arduino Pro series is meant for users that understand the limitations of system voltage...

It's blue! It's thin! It's the Arduino Pro Mini! SparkFun's minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader. Arduino Pro Mini does not come with connectors...

It's blue! It's thin! It's the Arduino Pro Mini! SparkFun's minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader. Arduino Pro Mini does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommend first time Arduino users start with the Uno R3. It's a great board that will get you up and running quickly. The Arduino Pro series is meant for users that understand the limitations of system voltage...

This is a 10-pin female header, with extra long legs -- great for stacking R3-compatible Arduino shields! Pins are spaced by 0.1". Documents: Datasheet ...

This is a 10-pin female header, with extra long legs -- great for stacking R3-compatible Arduino shields! Pins are spaced by 0.1". Documents: Datasheet

This is a 6-pin female header, with extra long legs -- great for stacking Arduino shields. Pins are spaced by 0.1". Documents: Datasheet ...

This is a 6-pin female header, with extra long legs -- great for stacking Arduino shields. Pins are spaced by 0.1". Documents: Datasheet

This is a 8-pin female header, with extra long legs -- great for stacking Arduino shields. Pins are spaced by 0.1". Documents: Datasheet ...

This is a 8-pin female header, with extra long legs -- great for stacking Arduino shields. Pins are spaced by 0.1". Documents: Datasheet

These headers are made to work with the Arduino Main Board, Arduino Pro, and the Arduino Mega. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields....

These headers are made to work with the Arduino Main Board, Arduino Pro, and the Arduino Mega. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit includes 4 headers (2 8-pin and 2 6-pin), enough to connect a shield to an Arduino Main Board. These are the same headers we use in our tutorials and with our own shields. Note: If you have a board that uses the Arduino R3 architecture which include the OREF, SCL, and SDA pins they can be...

This is the new Arduino Uno R3. In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations)....

This is the new Arduino Uno R3. In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory. No drivers needed for Linux or Mac (inf file for Windows is needed and included in the Arduino IDE), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. Never fear for accidental electrical discharge, either since since...

This is the new Arduino Uno R3. In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations)....

This is the new Arduino Uno R3. In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory. No drivers needed for Linux or Mac (inf file for Windows is needed and included in the Arduino IDE), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. Never fear for accidental electrical discharge, either since since...

"The ATmega128RFA1 is a portmanteau of sorts – two separate components combined to form one device; half microcontroller, half RF transciever. ATmega128RFA1 is an IEEE 802.15.4 compliant...

"The ATmega128RFA1 is a portmanteau of sorts – two separate components combined to form one device; half microcontroller, half RF transciever. ATmega128RFA1 is an IEEE 802.15.4 compliant single-chip, combining the industry- leading AVR microcontroller and best-in-class 2.4GHz RF transceiver providing industry’s highest RF performance for single-chip devices, with a link budget of 103.5dBm. The ATmega128RFA1 features Wake-on Radio, 32-bit MAC symbol counter, temperature sensor,...

    This is a ATmega328 IC in DIP package, pre-loaded with the Arduino Optiboot (Atmega328 16MHz) Bootloader. This will allow you to use Arduino code in your custom embedded...

    This is a ATmega328 IC in DIP package, pre-loaded with the Arduino Optiboot (Atmega328 16MHz) Bootloader. This will allow you to use Arduino code in your custom embedded project without having to use an actual Arduino board.     To get this chip works, you will need an external 16MHz crystal or resonator, and a 5V power supply to create the minimum Arduino system. If you are not comfortable doing this, we recommend you purchasing the Crowduino board...

The name says it all on this one. An ATmega328P in DIP package, pre-loaded with the Arduino Optiboot (Uno 16MHz) Bootloader. This will allow you to use Arduino code in your custom embedded project...

The name says it all on this one. An ATmega328P in DIP package, pre-loaded with the Arduino Optiboot (Uno 16MHz) Bootloader. This will allow you to use Arduino code in your custom embedded project without having to use an actual Arduino board. To get this chip working with Arduino IDE, you will need an external 16MHz crystal or resonator, a 5V supply, and a serial connection. If you are not comfortable doing this, we recommend purchasing the Arduino Uno board that has all of these built into...

"This is a small voltage and current sense PCB. DC current is determined by measuring a voltage drop across a pair of parallel shunt resistors, then converted to a final analog voltage output by the...

"This is a small voltage and current sense PCB. DC current is determined by measuring a voltage drop across a pair of parallel shunt resistors, then converted to a final analog voltage output by the TI INA-169. Voltage sense is accomplished by scaling to 3.3V ADC range by a precision resistor divider. The PCB is supplied without leads or connectors. The pad sizes are large enough to accommodate 12 gauge heavy duty leads (see datasheet) but care must be exercised in soldering. Smaller gauge...

This is a right-angle, 24-pin Molex Mini-Fit Jr.™ connector, commonly used as the power supply connector on ATX motherboards. Two rows of twelve pins are broken out two rows of through-hole male...

This is a right-angle, 24-pin Molex Mini-Fit Jr.™ connector, commonly used as the power supply connector on ATX motherboards. Two rows of twelve pins are broken out two rows of through-hole male headers. See the datasheet below for pin spacing dimensions. Pair this connector with a standard computer power supply and you can source a number of different voltages (+3.3V, +5V, +12V, -12V, -5V) to your project.[ Documents: Dimensional Drawing ...

Low profile 3.5mm stereo audio jack. Documents: Audio 3.5mm Jack Datasheet ...

Low profile 3.5mm stereo audio jack. Documents: Audio 3.5mm Jack Datasheet

AVR ISP Shield - PTH Kit Description: Did you know that your Arduino can spawn other Arduinos? Don't worry, it can't do it autonomously so you won't wind up with a replicator...

AVR ISP Shield - PTH Kit Description: Did you know that your Arduino can spawn other Arduinos? Don't worry, it can't do it autonomously so you won't wind up with a replicator situation (-gate, not -Trek). The point is, the ArduinoISP sketch allows your Arduino to act as a programmer. You can use this awesome power to burn bootloaders onto ATMega chips, turning them into Arduino-compatible microcontrollers! In the past, this required a breadboard and a whole mess...